Installing a new stereo in your vehicles is a good way to breathe in new life from the old driving days. Adding an MP3 or CD player can give the opportunity to listen to news, music and also improves the overall quality of sound on the cars sound systems. Performing the installation all by yourself is not easy. It requires dedication and patience. Every model of a car is different as well as its stereos. When it comes with car stereo san antonio, individuals can do the installation without any assistance.
Unplug all the connections from the old one. There will be lots of wiring at the back of the component and each one has to be disconnected. Unplug first the antenna wires. This is the thickest wire among the rest. Once remove, the component can be move freely. Unplug the wire connectors next. Unplug all the different colors and wires that are connected with the device.
When installing the new one, match up first the wires. Match the new wires from the cars harness to the new ones harnesses. Every connector and harness are unique in its own right it would be relatively easy to install the new ones because everything is being matched up with the same color. Just to be sure, check out the diagrams illustrated from the manual and see if everything is connected correctly.
Remove the trims. The trim will depend upon the classification and model of a car. Some are made of plastics so take note. If removing the trim is necessary, then include the drawers and knobs before prying it. Use a pry tool or your own hands to pry off the pieces of trims. The prying tools are specifically made for this purpose and it will never damage the pieces of trim.
Assemble and organize the mounting kits. If the new stereos have a mounting kit which is separated, then assemble it by following the instructions stated in the manual. Do not attempt to install the new one unless you adhere by the manual.
Tuck all in the wiring right through the dashboard. There might be some wires that will not slide back right inside the dashboard. Take the component with one hand and the other hand to tuck all the wires inside. Slowly tuck the wiring or else there might be a few wires that will need to be reconnected.
Pull out the equipment from its panel. Use a needle nose pliers to easily pull out the component. Simply give it a gentle pull. If the equipment does not budge or hard to pull, then there must be a few nuts that still in place. Double check the wiring and nuts once again.
Get referrals from your loved ones and friends. They may have done the procedure in the past and they can share some valuable information that might prove to be useful. Ask for tips in how to install the stereos.
It is important to gather as much information as possible before doing the installation all by yourself. This will eliminate the possibility that you are going to make a critical error. Also adhere the illustrations stated from the manufacturers manuals.
Unplug all the connections from the old one. There will be lots of wiring at the back of the component and each one has to be disconnected. Unplug first the antenna wires. This is the thickest wire among the rest. Once remove, the component can be move freely. Unplug the wire connectors next. Unplug all the different colors and wires that are connected with the device.
When installing the new one, match up first the wires. Match the new wires from the cars harness to the new ones harnesses. Every connector and harness are unique in its own right it would be relatively easy to install the new ones because everything is being matched up with the same color. Just to be sure, check out the diagrams illustrated from the manual and see if everything is connected correctly.
Remove the trims. The trim will depend upon the classification and model of a car. Some are made of plastics so take note. If removing the trim is necessary, then include the drawers and knobs before prying it. Use a pry tool or your own hands to pry off the pieces of trims. The prying tools are specifically made for this purpose and it will never damage the pieces of trim.
Assemble and organize the mounting kits. If the new stereos have a mounting kit which is separated, then assemble it by following the instructions stated in the manual. Do not attempt to install the new one unless you adhere by the manual.
Tuck all in the wiring right through the dashboard. There might be some wires that will not slide back right inside the dashboard. Take the component with one hand and the other hand to tuck all the wires inside. Slowly tuck the wiring or else there might be a few wires that will need to be reconnected.
Pull out the equipment from its panel. Use a needle nose pliers to easily pull out the component. Simply give it a gentle pull. If the equipment does not budge or hard to pull, then there must be a few nuts that still in place. Double check the wiring and nuts once again.
Get referrals from your loved ones and friends. They may have done the procedure in the past and they can share some valuable information that might prove to be useful. Ask for tips in how to install the stereos.
It is important to gather as much information as possible before doing the installation all by yourself. This will eliminate the possibility that you are going to make a critical error. Also adhere the illustrations stated from the manufacturers manuals.
About the Author:
Get a summary of the factors to consider before selecting an installer of car stereo San Antonio systems and more information about a knowledgeable installer at http://www.baudiosound.com/car-audio-system now.
No comments:
Post a Comment